Jigsaw Circle Cutting Guide & Compass: Perfect Radii & DIY Trammels

How to cut precision circles and round discs with a jigsaw: official trammel bar compasses, DIY pivot jigs, and zero-binding scroll blades.

Published by: Sierras de CalarLast reviewed on 3 min estimated read
Woodworker cutting a round circle disc with a jigsaw mounted to a pivot compass arm

Cutting freehand circles with a jigsaw almost always results in warped edges and blade wander. Using a circle-cutting compass attachment or a simple workshop trammel arm allows you to cut round tabletops and speaker holes with lathe-like precision.

Table of Contents View sections
  1. The Physics of Circle Cutting: Preventing Blade Twist
  2. Top Blades for Tight Curves and Circles
  3. The 3 Best Circle-Cutting Compass Setups
  4. Safety Checklist Before Powering On
  5. Frequently Asked Questions

The Physics of Circle Cutting: Preventing Blade Twist

Cutting curved radii with a jigsaw presents a unique challenge:

  • The outer edge of the kerf travels a larger circumference than the inner edge.
  • Standard straight-cutting blades (with wide 8mm to 10mm spines) rub aggressively against the inside radius wall.
  • This friction overheats the steel, forces the blade tip outward, and produces a beveled conical cut rather than a vertical 90-degree edge.

Equipping a narrow scroll blade is mandatory for clean circular cuts.

Top Blades for Tight Curves and Circles

  1. Bosch T 101 AO Clean for Wood (Fine, Splinter-Free Curves): Featuring a narrow 4.5mm back and pointed, biconvex ground teeth, it negotiates curves as tight as 4 inches (10 cm) without chipping veneers.
  2. Bosch T 244 D Speed for Wood (Fast Curved Cuts in Thick Timber): Aggressive side-set teeth combined with a narrow body make quick work of 2-inch timber and framing stock.

View Bosch T101AO curve blades on Amazon →

The 3 Best Circle-Cutting Compass Setups

1. Factory Parallel Guide with Compass Trammel Pin

Most leading jigsaw models (Bosch, Makita, DeWalt, Milwaukee) feature parallel edge guides with a built-in compass pivot pin:

  • Insert the steel guide rods through the shoe tunnels in reverse.
  • Position the center pivot pin into the center hole of your workpiece and tighten the wing thumb-screws.
  • The jigsaw pivots around the anchor pin in an exact, repeatable circle.

Shop jigsaw circle guides on Amazon US →

2. Shop-Made Plywood Trammel Arm (For Table Tops up to 5 Feet)

When cutting large circular dining tables or round patio furniture, factory guide rods are too short. Build a simple shop trammel:

  1. Cut a 1/4” plywood or hardboard strip to the desired radius length.
  2. Screw the jigsaw shoe securely onto one end with counter-sunk screws.
  3. Drill a clearance hole for the jigsaw blade.
  4. Drill pivot pin holes at your exact target radii and drive a nail or screw into the center of the workpiece.

3. Entry Plunge Holes for Internal Openings

If cutting a round speaker cutout or duct opening inside a panel:

  • Never try to plunge-cut freehand from the center.
  • Drill an entry hole right on the waste side of the layout line using a 1/2” Forstner or spade bit.
  • Insert the narrow blade while the jigsaw shoe rests completely flat, then start the cut.

View Forstner bit sets on Amazon US →

Safety Checklist Before Powering On

  • Check that the power cord and vacuum hose have full 360-degree clearance around the pivot center.
  • Support the waste disc with painter’s tape or shims as you complete the circle so it doesn’t drop and pinch the blade.

Frequently Asked Questions

What blade is best for cutting circles with a jigsaw?

Narrow scroll blades (such as the Bosch T101AO or T244D) are essential. Their narrow 4.5mm back prevents binding in the inner curve.

Back to Guides Overview