Jigsaw Circle Cutting Compass: Cutting Clean Radii in Aussie Timber

How Australian DIYers can cut round discs and holes with jigsaws using compass attachments and narrow scroll blades.

Published by: Sierras de CalarLast reviewed on 3 min estimated read
Tradesperson cutting a round timber tabletop using a jigsaw compass attachment

Freehand circle cuts usually turn into wavy ovals. Using a metal compass bar or a plywood trammel jig guarantees round discs every single time.

Table of Contents View sections
  1. The Physics of Circle Cutting: Preventing Blade Twist
  2. Top Blades for Tight Curves and Circles
  3. The 3 Best Circle-Cutting Compass Setups
  4. Safety Checklist Before Powering On
  5. Frequently Asked Questions

The Physics of Circle Cutting: Preventing Blade Twist

Cutting curved radii with a jigsaw presents a unique challenge:

  • The outer edge of the kerf travels a larger circumference than the inner edge.
  • Standard straight-cutting blades (with wide 8mm to 10mm spines) rub aggressively against the inside radius wall.
  • This friction overheats the steel, forces the blade tip outward, and produces a beveled conical cut rather than a vertical 90-degree edge.

Equipping a narrow scroll blade is mandatory for clean circular cuts.

Top Blades for Tight Curves and Circles

  1. Bosch T 101 AO Clean for Wood (Fine, Splinter-Free Curves): Featuring a narrow 4.5mm back and pointed, biconvex ground teeth, it negotiates curves as tight as 4 inches (10 cm) without chipping veneers.
  2. Bosch T 244 D Speed for Wood (Fast Curved Cuts in Thick Timber): Aggressive side-set teeth combined with a narrow body make quick work of 2-inch timber and framing stock.

View Bosch T101AO curve blades on Amazon →

The 3 Best Circle-Cutting Compass Setups

1. Factory Parallel Guide with Compass Trammel Pin

Most leading jigsaw models (Bosch, Makita, DeWalt, Milwaukee) feature parallel edge guides with a built-in compass pivot pin:

  • Insert the steel guide rods through the shoe tunnels in reverse.
  • Position the center pivot pin into the center hole of your workpiece and tighten the wing thumb-screws.
  • The jigsaw pivots around the anchor pin in an exact, repeatable circle.

Shop jigsaw circle guides on Amazon US →

2. Shop-Made Plywood Trammel Arm (For Table Tops up to 5 Feet)

When cutting large circular dining tables or round patio furniture, factory guide rods are too short. Build a simple shop trammel:

  1. Cut a 1/4” plywood or hardboard strip to the desired radius length.
  2. Screw the jigsaw shoe securely onto one end with counter-sunk screws.
  3. Drill a clearance hole for the jigsaw blade.
  4. Drill pivot pin holes at your exact target radii and drive a nail or screw into the center of the workpiece.

3. Entry Plunge Holes for Internal Openings

If cutting a round speaker cutout or duct opening inside a panel:

  • Never try to plunge-cut freehand from the center.
  • Drill an entry hole right on the waste side of the layout line using a 1/2” Forstner or spade bit.
  • Insert the narrow blade while the jigsaw shoe rests completely flat, then start the cut.

View Forstner bit sets on Amazon US →

Safety Checklist Before Powering On

  • Check that the power cord and vacuum hose have full 360-degree clearance around the pivot center.
  • Support the waste disc with painter’s tape or shims as you complete the circle so it doesn’t drop and pinch the blade.

Frequently Asked Questions

How do I start a cutout circle inside a board?

Drill an entry hole inside the waste area with a 10mm spade or Forstner bit before plunging the blade.

Back to Guides Overview